Toro Wheelmaster W323 (22318)

Toro Wheelmaster W323 (22318)

  • Easier “do-it-yourself” maintenance and lower repair costs
  • Better starting in cold conditions
  • Readily available fuel

The Toro W323 petrol Compact Utility Loaders are specifically designed for tough Australian conditions & are the most reliable compact utility loaders on the market. The labour saving wheeled models give you greater capability & effortless manoeuverbility so you can get more done with less time in a short learning curve-even for inexperienced operators. These machines are built to deliver a high power to-weight ratio in the compact utility loader category. They also have zero-turn manoeverability to handle countless jobs on every site ... dig, haul, plant & build.

  • 23 HP Kohler® petrol engine
  • Dual 15 litre fuel tanks
  • 2- pump system with combined flow of 56.4 lpm at 3,600 rpm
  • 2 ground speeds
  • Ride-on platform provides improved safety and visibility of working area and attachments
  • Easier ‘do-it-yourself’ maintenance and lower repair costs

Model #                                      
22318

Engine                                         
23hp Kohler Command Model CH23S 4 cycle, air cooled 2 cylinder

Power                                         
17.2 kW (23hp) at 3600 rpm (Gross, per SAE J1995)

14.4kW (19.3hp) at 2600 rpm (Gross, per SAE J1349)   

Peak Torque                             
44 Nm (33 ft-lbs) at 2600 rpm (Gross, per SAE J1995)    

Fuel Tank                                   
Dual rotationally moulded cross-linked high-density polyethylene fuel tanks with vented caps. A fuel shut-off valve in the fuel line near each tank   

Fuel Tank Capacity                 
Dual 15 litre fuel tanks

Battery                                       
The battery is a 12 volt, BCI group size U1, with 340 CCA minimum at –18 degrees C (0 degrees F) and, 38 minutes reserve capacity at 27 degrees C (80 degrees F) and 25 amp discharge rate per SAE J537L.

Electrical Interlocks               
The auxiliary power control lever and traction control levers must be in neutral (centre) position for the engine to start

Hydraulic Pump                       
Tandem gear pump connected to the engine crankshaft with flexible rubber couplers

Hydraulic Pressure                
224 bar (3250 psi) system relief pressure

Hydraulic Flow                         
Low-Flow Circuit: 15.5 lpm (3.4 gpm) at 3600 rpm

High-Flow Circuit: 40.9 lpm (9.0 gpm) at 3600 rpm         

Wheelbase                                
71.0 cm 

Wheels                                       
10.0 x 6.0 inches, five bolt, centre drop, heavy gauge steel

Ground Speeds                        
0-6.0 km/h (0-3.7 mph) forward or reverse (infinitely variable)                     

Ground Clearance                  
15.0 cm front; 15.0 cm rear

Auxiliary Power                     

Control                                       
A hydraulic valve lever in the front of the right handgrip above the control panel activates hydraulically powered attachments. Pull the lever rearward (non-detented) to operate the attachment in the forward direction, and push the lever forward (detented) to operate the attachment in the reverse direction          

Dimensions                               
Length: 208.8 cm w/bucket 157.5 cm w/o bucket

Width: 104.0 cm standard tyres; 90.0 cm narrow tyres

Height: 123.7 cm                                     

Hinge Pin Height                      
167.6 cm standard bucket – highest position  

Dump Height                            
119.4 cm with standard bucket

Dump Angle                              
34° standard bucket

Reach                                          
71.1 cm standard bucket

Maximum Operating            
231.7 cm

Height                                                          

SAE J818 Rating 50%             
234 kg (w/ 91 kg operator)

Tip Capacity                              

467 kg    

Weight                                        
711 kg (1,567 lbs) without attachment

777 kg (1,713 lbs) with standard bucket (model 22409)

Warranty
Standard warranty period of 2 years or 1000 hours limited warranty

Images may not reflect dealer inventory or unit specifications.

SHOWROOM

36 Abernethy Road
Belmont 6104
Western Australia
Australia

FREE CALL

1800 248 676

P +61 8 9478 7000
F +61 8 9478 6667

Brands we stock

  • Toro
  • Hako
  • Gianni Ferrari
  • Peruzzo
  • MTD
  • Cub Cadet
  • SMG
  • WALGA

© 2017 T-Quip 2017 All Rights Reserved